Infiniti QX50 Forum banner
1 - 17 of 17 Posts

·
Registered
Joined
·
361 Posts
Discussion Starter · #1 ·
2014 Infiniti QX50 - Push Button Ignition


To start the engine, press the brake pedal, and then push the ignition switch.

To stop the engine, move the shift lever to the Park position and push the ignition switch to the OFF position.

Pushing the ignition switch once, without applying the foot brake, will place the vehicle in ACC mode. When the ignition switch is pushed a second time, it will change to ON and a third time returns the ignition switch to OFF.

If the ignition is left in the ACC or ON position, various systems in the vehicle can discharge the battery and your vehicle may not start.

Allow the engine to idle for at least 30 seconds after starting. Do not race the engine while warming it up. Drive at a moderate speed for a short distance, especially in cold weather. During cold weather, allow the engine to run for a minimum of 2 - 3 minutes before shutting it off. Starting and stopping the engine over a short period of time may make the vehicle more difficult to start.

When leaving the vehicle, make sure that the ignition switch is placed in the LOCK position and that you take the Intelligent Key with you. As a precaution, if the driver's door is open while the ignition switch is in the ACC or ON position, a chime will sound.

If the Intelligent Key battery is discharged and you need to start the engine:
• First make sure the shift lever is in the Park position,
• Then insert the Intelligent Key into the key port. Make sure the Intelligent Key is placed in the correct direction: The front side faces upward and the key ring side faces the driver.
• Push the ignition switch while applying the brake pedal and the engine will start.
• If the brake pedal is not applied when the ignition switch is pressed, the ignition position changes to ACC.

The Intelligent Keyport does not charge the Intelligent Key battery. If you see the low battery indicator in the Dot Matrix Liquid Crystal Display, replace the battery as soon as possible.




2014 Infiniti QX50 - Windshield Wiper and Washer Controls


Your vehicle is equipped with an intermittent windshield wiper system.

This lever is used to control all windshield wiper and washer functions.

To operate the intermittent windshield wiper system, your ignition must be ON.

Push the lever down to the first stop for intermittent operation. To adjust the wiper speed, turn the knob toward the narrow markings for a faster operation or toward the wider markings for a slower operation.

Push the lever down to the second stop for continuous low-speed operation or down to the third stop for continuous high-speed operation.

In conditions of mist or light rain, push the lever up to MIST and you'll get a one-sweep operation of the wipers.

To operate the windshield washer, pull the lever toward you and hold. Washer fluid will spray and the wipers will sweep several times and stop.

When the Speed Sensing Wiper Interval function is turned on, your wiper speed will increase with an increase in vehicle speed.

To turn the speed sensing wiper interval function on or off, the ignition switch must be in the ON position. Press the SETTING button on the control panel. Select the OTHERS key. Then select the COMFORT key. Touch the Speed Sensing Wiper Interval key to turn the system ON or OFF.

To operate your rear windshield wiper at a preset intermittent speed; turn the knob on the end of the lever to INTERMITTENT.

For continuous low-speed operation, turn this knob to ON. Turn the knob to the OFF position to turn the rear windshield wiper OFF.

To clean the rear window, push this lever FORWARD. Washer fluid will spray and the wiper will automatically sweep several times and stop.




2014 Infiniti QX50 - Audio System with Navigation


Your vehicle's audio system features an AM/FM radio, a CD player, and SiriusXM® Satellite Radio, if so equipped.

Press the VOLUME ON/OFF knob to turn the audio system on. Turn the knob to adjust the volume.

Press the FM/AM button to set the radio band to AM, FM1 or FM2. For SiriusXM® Satellite Radio, press the XM button to set the radio band as XM1, XM2 or XM3.

A radio station can be found manually by turning the TUNE/FOLDER/AUDIO knob left or right to move up or down the dial through the stations. To tune and stop at the next broadcast station, press the SEEK/CATEGORY or TRACK buttons up or down. Press the SCAN button while in AM or FM mode to stop at each broadcasting station for five seconds. Press the SCAN button a second time to cancel scan tuning.

Up to 18 broadcast and 18 satellite stations can be set into memory. To choose the desired band, use the AM/FM/SAT select button for AM, FM1 or FM2, or satellite band XM1, XM2 or XM3.

To set a desired station, first choose a radio band by pressing the AM/FM/SAT button on the Infiniti multi-function control panel, then locate a station using the SEEK/CATEGORY, TRACK or SCAN buttons or radio tune knob.

Now, select and hold the desired station key, one through six, until the radio mutes. The station indicator will then come on and the sound will resume.

To play a stored station, select the radio band where it was stored then select the corresponding key, one through six.

To play a CD, insert the compact disc into the slot with the label side facing up. The disc will be guided into the slot and begin playing automatically. If the radio is already operating, it will automatically turn off and the compact disc will play.

To switch the audio system to play a CD that is already loaded while another audio source is active, press the DISC-AUXILIARY button repeatedly until the CD mode is shown on the display.

When playing a CD, the SEEK/CATEGORY button:

• Seeks the next track when the button is pressed, and
• Fast forwards the current track when the button is pressed and held.

When playing a CD, the TRACK button:

• Returns to the beginning of the current track and then seeks the previous track when the button is pressed, and
• Rewinds the current track when the button is pressed and held.

If the CD contains compressed audio files stored in folders, turning the TUNE/FOLDER/AUDIO knob moves through the folders.

To apply a random or repeat play pattern, touch the MENU key and then the PLAY MODE key. Touch the key of the desired play pattern to apply. The various random and repeat play modes can also be cycled through by pressing the RANDOM/REPEAT button.

Press the eject button to eject the CD.

This audio system is equipped with Speed Sensitive Volume (SSV), which increases volume at higher speeds and decreases it at lower speeds.

To enable or adjust the SSV:

• Press the SETTING button on the control panel,
• Touch the AUDIO key,
• Then touch the plus or minus keys on the Speed Sensitive Volume line.

The system will turn off when set to the lowest setting.

The same setting screen can be used to adjust bass, treble, balance or fade. Touch the plus or minus keys to change the bass or treble levels. Touch the L or R key to move the balance left or right, and the F or R key to fade the audio to the front or the rear of the vehicle.

For information on USB and iPod® features available with this audio system, please go to the USB/iPod® Interface chapter in the Vehicle Control section.

For information on the Bluetooth® streaming audio feature, please see the Bluetooth® streaming audio chapter in the Bluetooth® Technology section.




2014 Infiniti QX50 - Tire Pressure Monitoring System (TPMS)


The Tire Pressure Monitoring System (TPMS) monitors tire pressure. The CHECK TIRE PRESSURE warning message will appear in the vehicle information display and the low tire pressure warning light will illuminate when one or more tires are low on pressure and air is needed.

Adjust the low tire pressure to the recommended COLD tire pressure shown on the Tire and Loading Information label.

After tire pressures are adjusted, drive the vehicle at speeds above 16 miles per hour. The warning and indicator light will disappear.

If the low tire pressure warning light flashes for approximately one minute and then remains on after you turn the ignition ON, the TPMS is not functioning properly. Have the system checked by an Infiniti retailer.

Tire pressure rises and falls depending on the heat caused by the vehicle's operation and the outside temperature. Low outside temperature can lower the temperature of the air inside the tire, which can cause a lower tire inflation pressure. This may cause the low tire pressure warning light to illuminate.

If the warning light illuminates, check the tire pressure in your tires (including the spare tire). Check your tire pressure often and always prior to long distance trips.

The Tire and Loading Information label provides important information at a glance. It lists proper tire size and pressure. It also lists the maximum number of occupants for your vehicle and its maximum load capacity.

Please check your Owner's Manual for the location of the Tire and Loading Information label on your vehicle.

The Tire Pressure Monitoring System does NOT detect a sudden drop in tire pressure as with a tire blowout. And it is not a substitute for proper tire maintenance.




2014 Infiniti QX50 - AroundView® Monitor (if so equipped)


The Around View® Monitor is a parking aid that provides views of your vehicle's position in relation to surrounding objects. There are cameras located in the center of the front grille, on the outside mirrors and above the rear license plate.

The Around View® Monitor displays a combination of views with the ignition switch in the ON position.

• Bird's-eye View shows a top view all around your vehicle.
• Front-Side View shows the area around and ahead of the passenger's side front wheel.
• Front View shows the area directly in front of your vehicle.
• Rear View shows a picture of the area directly behind your rear bumper, and
• Rear-Wide View shows a wider picture of the area directly behind the vehicle.

Press the CAMERA button repeatedly to cycle through available view combinations or to return to the screen which was displayed before the CAMERA button was pressed.

The available views vary based on the position of the shift lever. Certain view combinations are displayed in a split-screen format. The camera display will not be shown when the vehicle speed is above approximately 6 miles-per-hour.

The front and rear views display the approximate distance between an object and your vehicle with colored lines.
• The RED line designates an object approximately 1.5 feet away.
• The YELLOW line designates an object is approximately 3 feet away.
• The first GREEN line designates an object is approximately 7 feet away.
• The second GREEN line designates an object is approximately 10 feet away.

When the steering wheel is turned, predictive course lines are also displayed on the screen. These lines show the approximate path the vehicle will take. The predictive course lines move in conjunction with how far the steering wheel is turned.

Please see your Owner's Manual for important safety information, system limitations and additional operating information.
 

·
Registered
Joined
·
361 Posts
Discussion Starter · #2 ·
2014 Infiniti QX50 - Destination Button


Press the DESTINATION button to set a destination and begin route calculation.

Before searching for a destination, check to see that the correct region is shown on the screen. If it needs to be changed, touch the CHANGE REGION key and select the correct region for your destination.

On the main destination screen, you can choose from the following by touching the key on the screen:

• STREET ADDRESS, prompts you to enter the address of the destination,
• PLACES, lets you search from a list of points of interest, such as gas stations, restaurants and hotels,
• HOME, sets as the destination an address previously saved as HOME,
• ADDRESS BOOK, shows a list of stored locations that can be set as the destination, and
• PREVIOUS DESTINATIONS, displays previous destinations that have been entered into the Navigation System.

Additional methods for setting a destination can be accessed by touching the NEXT PAGE key, including:

• DELETE DESTINATION, to delete the current destination and waypoints.
• PREVIOUS START POINT, which sets the previous route's starting point as the destination,
• STORED ROUTES, to choose the destination from a list of previously stored routes,
• PHONE NUMBER, to search for a destination using the phone number,
• FREEWAY ENTRANCE/EXIT, for setting a freeway entrance or exit as the destination,
• INTERSECTION, to set the intersection of two streets as the destination, and
• CITY CENTER, for setting the center of a chosen city as the destination.

It is also possible to set the destination using the map. To do this, move the map so that the cross pointer is centered on the location you wish to set as the destination. Press the ENTER button on the Infiniti Controller and then touch NEW DESTINATION.




2014 Infiniti QX50 - Lane Departure Warning (LDW) and Lane Departure Prevention (LDP)


The Lane Departure Warning (LDW) and Lane Departure Prevention (LDP) Systems, if so equipped, are activated at speeds of approximately 45 miles per hour and above. These systems monitor the lane markers on the traveling lane using a camera unit located in front of the inside mirror.

The LDW system is activated when the camera detects that the vehicle is approaching the left or the right side of the traveling lane. A blinking Lane Departure Warning indicator light appears in the instrument panel and a warning chime sounds.

The LDP system is activated by the same conditions as the LDW system. In addition to alerting the driver with a warning chime and the Lane Departure Warning indicator light in the instrument panel, the system automatically applies the brakes briefly on the appropriate side of the vehicle to help return the vehicle back to the traveling lane.

To enable or disable the LDW system, press the WARNINGS SYSTEM SWITCH

To enable or disable the LDP:

• Press SETTING button on the control panel,
• Push the DRIVER ASSISTANCE key,
• Push the DYNAMIC ASSISTANCE SETTINGS key, and then
• Push the LANE DEPARTURE PREVENTION key to toggle this feature on or off.

Once enabled, the LDP system can be activated by pushing the Dynamic Driver Assistance switch on the right side of the steering wheel.

Please see your Owner's Manual for important safety information, system limitations and additional operating information.




2014 Infiniti QX50 - DVD Player (with Navigation System only)


If so equipped, this system allows you to view a DVD movie on the front display.

To play a DVD, place the ignition switch in the ACC or ON position, move the shift lever to PARK and apply the parking brake.

Press the POWER button on the audio system and insert a DVD into the CD slot. Be sure that the label of the DVD faces up when loading. The player will automatically load and begin to play the DVD.

While a DVD is playing, press the DISC/ AUXILIARY button to display additional DVD options. Press a key on the touch screen to select or adjust the desired feature. The Infiniti controller can also be used to select and adjust items. Use the controller to highlight an option on the screen, then press the ENTER button.

Use the SKIP keys to skip forward or backward through multiple chapters. Select the CM SKIP keys to fast-forward or rewind the DVD by the set amount defined in the DVD SETTINGS menu.

While a DVD is playing, touch the screen to activate the menu, then select TOP MENU and the top menu specific to each disk will play.

Select the SETTINGS key to access a menu of additional options for the DVD player.

Press the EJECT button on the audio system to eject the DVD from the player.

Please see your Owner's Manual for important safety information, system limitations and additional operating information.




2014 Infiniti QX50 - Map Button (if so equipped)


Press the MAP button to display the current location's map screen.

Use the arrows on the touch screen to move around a map. When you start moving, a cross pointer appears. Stop when the pointer is where you want it and press the ENTER button on the Infiniti Controller.

The directional keys on the Infiniti Controller can also be used to move around the map screen.

To view the map in greater detail, touch the scale indicator on the screen and then touch THIS key to zoom in, or THIS key to zoom out.

When a map screen is displayed, touching the MAP MENU key will show a list of additional options.

Touch STORE LOCATION to store the current location in the address book to be used later as a destination or waypoint.

Touch NEARBY PLACES to see a list of points of interest near the current location, such as gas stations and restaurants.

Touch MAP VIEW to change the map orientation. Available options are:

• 2D,
• SPLIT 2D,
• BIRDVIEW, and
• SPLIT BIRDVIEW format.

The 2D VIEW shows a map in the two dimensional form that is similar to a road map.

The SPLIT 2D, also shows two maps in the two dimensional format, but shows a close-up of one and a wider view of the other.

The BIRDVIEW map makes a route more recognizable because it elevates the landmarks and provides a panoramic view over a long distance.

If you choose SPLIT BIRDVIEW, you can look at both views at once on a split screen.

Touch MAP ICONS to toggle on or off various types of icons to display on the map.

Touch STORE TRACKING to store the route that has been traveled from the starting point to the current location in the address book.




2014 Infiniti QX50 - Outside Mirrors


When the ignition switch is in the ACC or ON position, you'll be able to adjust your outside mirror by remote control.

The outside mirror control switch is located on the armrest.

To begin, turn the outside mirror control switch to the right or left, depending on which side you want to adjust.

Then move the switch left, right, up or down to move each mirror to the desired position.

Once the mirrors are in place, return the switch to the Neutral position to avoid accidently changing the mirror positions.

If your vehicle is equipped with the Reverse, tilt-down feature, the selected outside mirror surface will turn downward to provide better rear visibility close to the vehicle.

To use, turn the ignition switch to the ON position and select the left or right outside mirror. Move the shift selector to (R) or Reverse and the selected mirror will turn downward. Only one mirror is active at a time.

The selected mirror surface will return to its original position when any of the following have occurred:
• The shift selector is moved to any position other than (R) or Reverse.
• The outside mirror control switch is set to the Neutral or center position.
• Or the ignition switch is placed in the OFF position.

The outside mirrors along with the rear window glass can be heated to defrost, defog or de-ice for improved visibility.

Once the engine is started, push the rear window defroster switch. The indicator light will be illuminated on the display screen.

The rear window defroster automatically turns off after about 15 minutes. To turn it off sooner, you can push the defroster switch a second time.
 

·
Registered
Joined
·
361 Posts
Discussion Starter · #3 ·
2014 Infiniti QX50 - Bluetooth Hands-Free Phone System without Navigation Operating Tips


These controls allow you to operate the Bluetooth® system from your steering wheel. Here are some helpful tips to get the most out of your Bluetooth® system.

• For recommended phones and detailed instructions for connecting a compatible cellular phone, please visit Infiniti Bluetooth | Wireless Phone Technology | Infiniti USA.
• When using the Bluetooth® system, keep the interior of your vehicle as quiet as possible. Close windows and direct air vents away from the roof and your face.
• To operate the voice recognition system, press and release the PHONE/SEND button on the steering wheel. The in-vehicle microphone receives the command and the system provides voice feedback when the command is accepted.
• Wait until the system tone sounds before speaking a command. Begin speaking within five seconds after the tone sounds.
• Speak in a natural voice without pausing between words.
• Say "Help" at any time to hear a list of available commands.
• You can press the PHONE/SEND button to skip prompts at any time.
• Use single digits when speaking phone numbers. For example, "five hundred" should be spoken as "five zero zero."
• To increase or decrease the volume of the phone prompts, push the volume control switches on the steering wheel, plus or minus, or turn the volume control dial on the audio system if in operation.
• To cancel a voice recognition session, simply wait five seconds, say "Cancel," "Quit" or press and hold the PHONE/END button.

For more information on your Bluetooth® system, see your Owner's Manual or visit Infiniti Bluetooth | Wireless Phone Technology | Infiniti USA.




2014 Infiniti QX50 - Making, Receiving, and Ending a Call Non-Navi (if so equipped)


To make a call, press the PHONE/SEND button on the steering wheel. The system will announce a list of available commands. After the tone, say "Call."

From the next menu of voice commands, you may then say:

• A name from the vehicle phonebook. The system asks you to confirm the selection. Say "Yes" to dial the entry.
• PHONE NUMBER, to dial a phone number by speaking the digits when prompted.
• REDIAL, to have the system call the last outgoing number dialed, or
• CALL BACK, to dial the phone number of the last incoming call.

You can say "Help" at any time to hear a list of the available voice commands.

While a call is active, pressing the PHONE/SEND button on the steering wheel allows additional voice commands, including:

• SEND, to input digits.
• TRANSFER CALL, to switch the call from the Bluetooth® system to the handset, or
• MUTE, to mute your voice to the other end of the call.

To end a call, press the PHONE/END button on the steering wheel.

When an incoming call is placed to the connected phone, the ringtone will sound through the Bluetooth® system. To answer the call, press the PHONE/SEND button. To reject the incoming call, press the PHONE/END button on the steering wheel.




2014 Infiniti QX50 - Power Seat Adjustments


Look for this switch on the side of your seat. Slide it forward or backward and the seat will move in that direction.

This switch can also be used to adjust the height and angle of the seat. Move the front or rear end of the switch up or down to adjust the angle of the cushion. Then push down or pull up on the middle of the switch to adjust the height.

To recline the seat, push this switch backward until you achieve the desired position. To bring the back upright, push the switch forward.

The lumbar support feature provides lower back support to the driver.

To adjust the manual lumbar support (if so equipped), move this lever up or down.

To adjust the power lumbar support (if so equipped), push the front end of this switch to extend the lumbar support, or push the back end to retract it.

There are multiple ways to fold the 2nd row seat flat for maximum cargo hauling. To fold the seats manually pull the lever located on the top outboard side of the seatback and fold the seat.

If you are in the back of the vehicle with the liftgate raised, push the front of the switch located on the left or right side of the luggage room and the corresponding seatback will fold.

To return the second row seats to an upright position manually, push up on the seatback until it latches in place.

To return the seatback while in the drivers seat or front passengers seat, press and hold the switch located on the center console until the corresponding seatback is fully returned.

If your vehicle is equipped with type A seat and switch, you can raise the seatback from the rear of the vehicle with the liftgate up. Just push and hold the rear side of the switch in the luggage room and the corresponding seatback will return.




2014 Infiniti QX50 - Fuel Functions


Located in the instrument cluster, this gauge indicates the approximate fuel level in the tank.

This light comes on when the fuel level is low. Refuel as soon as practical. You'll see an arrow next to the fuel pump icon that indicates the side of the vehicle where the fuel-filler door is located.

The fuel-filler door automatically unlocks when the driver's door is unlocked. To open the fuel-filler door, exit the vehicle, and push the left side of the fuel-filler door.

To remove the cap, turn it counterclockwise. Put the cap in the holder on the fuel-filler door while you're refueling.

After fueling, turn the cap clockwise until a single click is heard, indicating the cap is locked, and then securely close the fuel-filler door.

This message appears in the vehicle information display when the fuel cap is not attached properly. If this occurs:
• Exit the vehicle and reinsert the fuel-filler cap straight into the fuel-filler tube,
• Turn the fuel-filler cap clockwise and tighten until a single click is heard,
• Then press this button on the right side of the steering wheel for more than one second to turn the indicator OFF.

Failure to properly tighten the fuel-filler cap after the Loose Fuel Cap warning message is displayed, may cause the Malfunction Indicator Light to illuminate.

If you have taken the appropriate steps and the indicator light does not turn off, please see your Infiniti retailer for further assistance.




2014 Infiniti QX50 - HomeLink® Universal Transceiver (if so equipped)


Your HomeLink® Universal Transceiver's control buttons are located along the bottom of your rearview mirror. The system can consolidate the functions of various individual hand-held transmitters to replace devices that operate garage doors, gates, lights or security alarms. HomeLink® is powered by your Infiniti vehicle's battery and requires no other power source.

Remember that you'll need all of your hand-held transmitters, such as your garage door opener, to successfully program HomeLink®.

To get started, clear the memory by pressing and holding the two outer HomeLink® buttons, for approximately 10 seconds. When the indicator light begins to blink, release both buttons.

Now you're ready to program.

To begin programming, position the hand-held transmitter 1 to 3 inches away from the HomeLink® surface.

Now, using both hands, simultaneously press and hold both the HomeLink® button you want to program and the hand-held transmitter button until the indicator light flashes, changing from a slow blink to a rapid blink.

When the indicator light flashes rapidly, both buttons may be released. The rapidly flashing light indicates that the device has been successfully programmed.

To activate a programmed device, press and hold the programmed HomeLink® button. If the indicator light is solid, training is complete and your device should activate when the HomeLink® button is pressed and released.

If the indicator light blinks rapidly for 2 seconds and then turns to a solid light, there are additional steps required to program your device. See your Owner's Manual for more information.

If you have any questions or are having difficulty programming your HomeLink® buttons, please refer to the HomeLink® web site at: HomeLink or call 1-800-355-3515.
 

·
Registered
Joined
·
361 Posts
Discussion Starter · #4 ·
2014 Infiniti QX50 - Intelligent Cruise Control (Full Speed Range)(if so equipped)


If your vehicle is equipped with the Intelligent Cruise Control, or ICC, system, it works like a standard cruise control only with the added feature of maintaining a selected distance from the vehicle in front of you.

The ICC system offers two cruise control modes:
• Vehicle-to-vehicle distance control mode maintains a selected distance between you and the vehicle in front of you.
o The distance to the vehicle ahead can be selected at any time depending on the traffic conditions.
o Each time the DISTANCE switch is pushed, the set distance will change to long, middle, short and back to long again in that sequence.
o The distance to the vehicle ahead will change according to the vehicle speed. The higher the vehicle speed, the longer the distance.
o If the vehicle in front is traveling slower than your set speed, the ICC will automatically match that vehicle's speed. Once the road ahead clears, the ICC will resume your set speed automatically.
o Each time the engine is started, the initial setting becomes "Long".

• When the road ahead is clear, the driver can set the speed range between approximately 20 to 90 miles per hour.

• Or, you may choose the conventional, or fixed speed, cruise control mode for cruising at a preset speed.

• To switch between the two cruise control modes you must first turn the system OFF, and then turn it ON again in order to select the other cruise control mode.

To set the ICC system, push and quickly release the CRUISE ON/OFF switch and you'll be in the vehicle-to-vehicle distance control mode.

For the conventional or fixed speed cruise control mode, push and hold the CRUISE ON/OFF switch for longer than approximately 1.5 seconds.

You can confirm the setting of the Intelligent Cruise Control system in the vehicle information display.


The detection range of the sensor is approximately 390 feet in front of you. It will not detect the following objects:
• Stationary and slow moving vehicles
• Pedestrians or objects in the roadway
• Oncoming vehicles in the same lane

Please see your Owner's Manual for important safety information, system limitations and additional operating information.




2014 Infiniti QX50 - Intelligent Key® and Locking Functions


Without removing the Intelligent Key from your pocket or purse, you can lock or unlock your doors, open the liftgate and start the engine.

To unlock the vehicle, have the Intelligent Key with you and then push the request switch on the door handle. That door will now unlock. Push the switch again within one minute to unlock all doors and the liftgate.

To lock your vehicle, push any door handle's request switch once, after all doors have been closed.

The Intelligent Key has lockout protection. If the power door lock switch is moved to the lock position with any door open and the Intelligent Key in the vehicle, all doors unlock immediately and a warning chime sounds as soon as the door is closed.

These lock and unlock functions are operational when the Intelligent Key is within about 2 1⁄2 feet of a request switch.

To activate the panic alarm, press this button for more than one second. The panic alarm will sound and the headlights will stay on for a period of time.

The Intelligent Key can also be used to operate door locks and windows from outside the vehicle, at a distance of up to 33 feet. To lock doors, press the LOCK button. Your hazard warning lights will flash twice, your horn will beep once, and you'll know that all doors are locked.

To unlock the doors, press the UNLOCK button. The hazard warning lights will flash once and the driver's door will unlock. Press again within one minute to unlock all doors and the liftgate. All doors will automatically relock within one minute unless you push the ignition switch or open any door.

Hold the UNLOCK button for more than 3 seconds after the doors are unlocked to lower the automatic windows.

In a rare instance when your Intelligent Key battery is discharged, you can still use the Mechanical Key to lock or unlock the vehicle.

You'll find the Mechanical Key concealed on the back of the Intelligent Key. To remove it, release the lock knob on the back of the Intelligent Key and slide the Mechanical Key out. Then insert the Mechanical Key into the key cylinder on the driver's door and turn to lock or unlock the vehicle.

When you leave a key with a valet, your Intelligent Key can help you keep your belongings safe in your vehicle. Use the Mechanical Key to lock the glove box. You can then give the Intelligent Key to the valet and take the Mechanical Key with you.

As many as four keys can be used with one vehicle, provided the Intelligent Keys are registered with the Infiniti retailer prior to use with the Intelligent Key system.

The Intelligent Key contains sensitive electrical components. Please avoid these circumstances that could affect its operation:
• Avoid dropping or striking it against another object
• Keep it away from water
• Keep it away from equipment with magnetic fields, including computers, cell phones, TVs, and audio accessories, and
• Avoid using a key chain that contains a magnet




2014 Infiniti QX50 - Making a call (if so equipped)


To make a call using the Bluetooth® Hands-Free Phone System, first press the PHONE/SEND button on the steering wheel.

The PHONE screen will appear on the center display.

You may then touch:

• Quick Dial, to select a quick dial entry.
• Phonebook, to select the name from an entry stored in the phonebook, or
• Call History, to choose a number from the incoming or outgoing call history.

You can also use voice recognition to make a phone call. To do this:

• Press the TALK button on the steering wheel and say "Phone,"
• When prompted, say "Phonebook."
• Speak a name from your phonebook after the tone.

When speaking phone book names, please be aware some phones require the last name to be spoken before the first name. For example, "Michael Smith" may be spoken as "Smith, Michael."

To dial by phone number:

• Press the TALK button on the steering wheel and say "Phone,"
• Wait for the tone and then say "Dial Number."
• When prompted by the system say the digits of the phone number you wish to dial, starting with the area code.

You can speak all ten digits of the phone number without pausing. If the system has trouble recognizing the correct phone number:

• Speak the three digits for the area code, and pause briefly
• then three digits for the prefix, pause briefly, and
• then the last four digits.




2014 Infiniti QX50 - Conventional Cruise Control (Fixed Speed)


Cruise Control enables you to set a desired speed between 25 and 90 miles per hour -- and remain there until you wish to slow down, accelerate or stop.

Your vehicle may be equipped with Intelligent Cruise Control or ICC. If you have the ICC system, turn on the conventional fixed-speed cruise control by pushing and holding the steering wheel CRUISE ON/OFF switch for longer than approximately 1.5 seconds.

If you do not have the ICC system, push the ON/OFF switch and the CRUISE indicator light will illuminate. Accelerate until you reach the desired speed. Then push down on the COAST/SET switch -- and release it. The CRUISE SET indicator light will illuminate and your vehicle will operate at your selected speed.

If you need to pass another vehicle, assure that it is a legal maneuver, then press the accelerator pedal. Once you have safely passed, release the accelerator and your vehicle will return to the previously set speed.

To change to a faster cruising speed, push UP and hold the ACCELERATE/RESUME switch. Release at your desired cruising speed. If you push and quickly release this switch, each push will increase your set speed by about one mile per hour.

To reset at a slower cruising speed, push DOWN and hold the COAST/SET switch. Release when you have reached the desired slower speed. If you push and quickly release this switch, each push will decrease your set speed by about one mile per hour.

To cancel Cruise Control, push CANCEL, or tap your brake pedal. To resume cruising at your last set speed, push UP on the ACCELERATE/RESUME switch. To turn Cruise Control OFF completely, push the ON/OFF switch.

Please see your Owner's Manual for important safety information, system limitations and additional operating information.




2014 Infiniti QX50 - Power Moonroof


To operate the power moonroof, place the ignition in the ON position.

To fully open or close the moonroof, push the OPEN or CLOSE side of this switch and release it. You do not need to hold it.

To partially open or close the moonroof, push the switch in any direction. When the moonroof has reached the desired position, push the switch once more to stop it.

To tilt the moonroof up, first close the moonroof then push the switch to the TILT UP position and release it. To tilt it down, push the switch to the TILT DOWN position.

Manually open and close the sunshade by sliding it forward or backwards. The sunshade will open automatically when the moonroof is opened.

If you've turned the ignition OFF and notice the moonroof is open, you still have a period of time in which to close it. However, if either front door is opened during that period, power to the moonroof is canceled.

If the moonroof does not operate properly, perform the following procedure to initialize the moonroof:
1. Place the ignition switch in the ON position.
2. If the moonroof is open, fully close it by repeatedly pushing the CLOSE side of the moonroof switch.
3. Push and hold the CLOSE side of the moonroof switch.
4. Release the moonroof switch after the moonroof moves slightly up and down.
5. Push and hold the OPEN side of the moonroof switch to fully tilt the moonroof down.
6. Check to see if the moonroof switch operates properly.

Initialization is complete if the moonroof operates properly. If it does not, see your INFINITI retailer for service.
 

·
Registered
Joined
·
361 Posts
Discussion Starter · #5 ·
2014 Infiniti QX50 - USB/iPod® Interface


Your vehicle is equipped with a USB jack. It is located in the center console box. Plug a compatible storage device into the jack and play audio files stored on the device.

To play an iPod®, connect the cable supplied with your iPod® to the USB jack, then connect the other end of the cable to your iPod®. If compatible, the battery of your iPod® will charge while connected to the vehicle.

When closing the center console lid, please make sure the cord is routed through this notch to ensure lid closure and cord integrity.

Once a device is plugged into the jack, press the DISC/AUXILIARY button repeatedly to switch to the USB or iPod® mode.

Depending on the version of the iPod®, the display on the iPod® shows an INFINITI or "Accessory Attached" screen when the connection is active. When the iPod® is connected to the vehicle, the iPod® music library can only be operated by the vehicle audio controls.




2014 Infiniti QX50 - Automatic Drive Positioner (if so equipped)


The automatic drive positioner, if so equipped, enables you to store two sets of positions for the driver's seat, steering column and outside mirrors using these controls on the driver's side door.

To save a set of positions:

• First, ensure that the shift lever is in the Park position and that the ignition is switch is in the ON position.
• Adjust the driver's seat, steering column and outside mirrors to the desired positions by manually operating each adjusting switch,
• Push the SET switch and, within five seconds, push the memory switch one or two, for at least one second.
• The indicator light for the pushed memory switch will come on and stay lit for approximately five seconds.
• When the indicator light goes off and, if so equipped, a chime sounds, the procedure is complete.

When a new set of positions is saved to memory, the previously stored positions for that switch are deleted.

Stored memory positions can also be linked to an Intelligent Key. First, create a stored memory position. Then, during the final step when the indicator light for the memory switch being set is illuminated for 5 seconds, press the unlock button on the Intelligent Key you wish to link.

For a second driver, repeat this procedure using the other Intelligent Key.

If your vehicle is equipped with the Entry / Exit Function, the driver's seat will slide backward and the steering wheel will move up when:

• The driver's door is opened with the ignition switch in the LOCK position, or
• The ignition switch is moved from the ACC to LOCK position with the driver's door open.

The driver's seat and steering wheel will return to the previous positions when:

• The driver's door is closed with the ignition switch in the LOCK position, or
• The ignition switch is moved from the ACC to ON position with the shift lever in Park.




2014 Infiniti QX50 - Setting Button (if so equipped)


Use this button to customize the settings of the various electronic systems in your vehicle. You can adjust Navigation, Audio, Phone, Bluetooth®, Volume and Beeps, Display, Clock and Others by pressing the SETTING button. Use the touchscreen to choose a setting function you wish to adjust.

Selecting "Navigation" will provide options for setting the Navigation System.

Select "Audio" to adjust features such as Bass, Treble, Balance, Fade and Speed Sensitive Volume.

The "Phone" and "Bluetooth" screens provide numerous options for operating your Bluetooth® Hands-free Phone System, including phonebook and ringtone settings.

The "Volume and Beeps" menu allows you to adjust the volume and status of the Guidance Voice, Phone options and Beep functions.

Selecting "Display" will allow you to adjust the color theme, brightness, contrast and background color.

Selecting "Clock" enables you to set and adjust clock functions.

Select "Others" to access the "Language and Units" menu. This feature lets you change the language and measurement unit used in the system.





2014 Infiniti QX50 - Blind Spot Warning (BSW) (If so equipped)


The Blind Spot Warning system can help alert the driver of other vehicles in adjacent lanes.

The Blind Spot Warning system uses radar sensors installed near the rear bumper to detect other vehicles in an adjacent lane.

When the radar sensor detects vehicles in the detection zone and the vehicle is traveling at speeds greater than 20 miles-per-hour, the Blind Spot Warning indicator located on the driver's door inside the outside rearview mirror illuminates.


If the driver then activates the turn signal, the system chimes twice and the Blind Spot Warning indicator light will flash.

To enable or disable the BSW system, press the warning systems switch.

Please see your Owner's Manual for important safety information, system limitations and additional operating information.




2014 Infiniti QX50 - Speaker Adaptation (if so equipped)


The Speaker Adaptation function is designed to learn the specific sounds of your voice, making voice commands easier for the system to recognize.

To begin training the system for your voice, press the SETTING button on the control panel and touch the OTHERS key on the display screen.

Touch the VOICE RECOGNITION key, then touch the SPEAKER ADAPTATION key.

The Speaker Adaptation function can memorize the voices of up to three users.

Touch USER 1, USER 2 or USER 3.

Touch "Start Speaker Adaptation Learning."

Next, select a category from the list on the screen by touching one of the following:

• Phone
• Navigation
• Information
• Audio
• Help

The voice commands in the chosen category are displayed. Touch a command on the screen. After the tone sounds and the mouth on the voice icon on the screen changes from closed to open, speak the command.

If the system has learned the command correctly, the voice command indicator on the screen turns on. Touch the BACK key to return to the previous screen and repeat the process for other voice commands.
 

·
Registered
Joined
·
361 Posts
Discussion Starter · #6 ·
2014 Infiniti QX50 - Instrument Brightness Control


The Instrument Brightness Control Switch is located on the left of the instrument cluster.

Your instrument panel lights up whenever the ignition is ON, the parking lights or headlights are ON, or in the AUTO position with the exterior lights activated.

To increase the brightness, press the PLUS button. To decrease the brightness, press the MINUS button. When adjusting, a BRIGHTNESS indicator will appear on the vehicle information display.




2014 Infiniti QX50 - Parking Brake and Indicator


The parking brake is located to the left of the brake pedal.

To apply the parking brake, fully depress this pedal. To release, depress the parking brake pedal a second time with your left foot while your right foot is firmly placed on the foot brake pedal to keep the vehicle from moving.

This indicator light comes on when the ignition is ON and the parking brake is applied. When releasing the parking brake, make sure the light is OFF before driving.




2014 Infiniti QX50 - Day/Night OFF Button (if so equipped)


The DAY/NIGHT OFF button displays alternate views of a day screen and a night screen. Press this button for more than two seconds to turn the display OFF. Press again to turn the display ON.

You can also adjust the screen brightness in either Day or Night setting by pressing the Day/Night OFF button and then turning the INFINITI controller to increase or decrease the brightness.




2014 Infiniti QX50 - Forward Collision Warning (FCW) System (if so equipped)


The Forward Collision Warning (FCW) system warns you when you are getting close to the vehicle ahead by illuminating a warning light on the instrument panel and sounding a chime. The FCW system functions when your vehicle is driven at speeds of approximately 10 miles-per-hour and above.

The FCW system is automatically turned on when the ignition switch is pushed to the ON position. When the FCW system is on, the warning systems ON indicator light illuminates.

To turn the FCW system OFF, push the warning systems switch. The warning systems ON indicator light will turn off. To turn the system ON, push the warning systems switch again.

Please see your Owner's Manual for important safety information, system limitations and additional operating information.




2014 Infiniti QX50 - Headlights and Exterior Lights


The headlight switch is located on the multifunction lever to the left of the steering column.

To turn ON your front parking lights, tail lights, license plate light and instrument panel lights, turn the headlight switch to THIS position. To turn ON the front headlights, turn the switch to THIS position. All the other lights will stay ON.

To turn ON your high beam headlights, push this lever forward. You'll see a blue indicator light illuminate. Pull it back toward you to return to low beam. The blue light will turn off. To make your high beam headlights flash ON and OFF, pull the lever toward you and release it.

Fog lights create a wide beam pattern, focused lower than the headlights. This minimizes reflected light and helps you see better in foggy conditions. To use the fog lights, your headlights must be ON and low beam selected. Rotate the collar to THIS position and your fog lights will come ON. Rotate the collar to the OFF position to return to low beam and deactivate the fog lights. If you turn the high beam headlights ON, the fog lights will automatically turn OFF.

You can preset the headlights to automatically operate based on exterior lighting conditions. To activate this system, move the headlight switch to the AUTO position, and push the ignition switch to the ON position.

To turn the system OFF, turn the headlight switch to any other setting. The Autolight system will also keep the headlights ON for a period of time after you push the ignition switch to the OFF position.

There is a light sensor that controls the Autolight system on the top of the instrument panel. Keep that area clear of papers and other material.
 

·
Registered
Joined
·
361 Posts
Discussion Starter · #7 ·
2014 Infiniti QX50 - Adjustable Head Restraints and Headrest


Your vehicle's front and 2nd row outboard seats are equipped with adjustable head restraints that may help provide protection against injury in certain accidents.

Your vehicle is equipped with a non-adjustable headrest in the second row center seat.

The head restraint should be placed so its center is in line with the center of the ear.

If your ear position is still higher than the recommended alignment, place the head restraint at the highest position.

To raise the head restraint, pull up. To lower, press and hold the LOCK knob while pushing the head restraint down.

Your vehicle's front seats are equipped with active head restraints that move forward during a rear-end collision to absorb some of the forces that may lead to whiplash. The active head restraints will only operate in certain situations and will return to their original position after the collision.

Please see your Owner's Manual for important safety information, system limitations and additional operating information.




2014 Infiniti QX50 - Interior Lights


Map lights are located above the rearview mirror. Push the lens of either light to turn it ON or OFF.

When the switch is in the DOOR position, the map lights and rear personal lights will illuminate under the following conditions:
• ignition switch is switched to the LOCK or OFF position
• doors are unlocked by pushing the UNLOCK button on the Intelligent Key or door handle request switch with the ignition switch in the LOCK or OFF position
• any door is opened and then closed with the ignition switch in the LOCK or OFF position
• any door is opened with the ignition switch in the ACC or ON position.
This switch controls the light in the cargo area of the vehicle. When this switch is in the ON position, the cargo light illuminates and remains on.
If the switch is moved to the center position, the cargo light illuminates and will remain on as long as the liftgate is open. When the switch is in the OFF position, the cargo light will remain off.




2014 Infiniti QX50 - Vehicle Dynamic Control (VDC)


The Vehicle Dynamic Control (or VDC) system uses various sensors to monitor driver inputs and vehicle motion.

Under certain driving conditions, it controls brake pressure and engine output to help the driver maintain control of the vehicle. VDC should remain ON when driving, except when freeing the vehicle from mud or snow.

When you push the VDC OFF switch located behind the steering wheel, an indicator light will illuminate. If you have turned OFF the VDC system, it will turn back ON when you push the switch a second time.

Also, when you turn OFF and then restart your vehicle, the system will automatically come on again.

Please see your Owner's Manual for important safety information, system limitations and additional operating information.




2014 Infiniti QX50 - Voice Prompt Interrupt (if so equipped)


When using the Voice Recognition system, it is possible to skip the system's voice prompts.

Press the TALK button on the left side of the steering wheel. The system responds with a list of instructions or available commands. It is not necessary to wait for the system to finish speaking.

Simply press the TALK button a second time when the system is giving audio voice commands. You can speak a command once the tone sounds and the face icon changes on the display screen.

This procedure can be repeated anytime you wish to interrupt the voice prompt.




2014 Infiniti QX50 - Bluetooth Streaming Audio (if so equipped)


If your vehicle is equipped with Bluetooth® Streaming Audio, you can access and play audio files from your Bluetooth® compatible device.

If the desired Bluetooth® audio player is already paired as a phone, press the SETTING button on the control panel. Touch BLUETOOTH on the display screen, then CONNECTED DEVICES, and then AUDIO PLAYER. Select your already paired phone as an audio player by touching its name on the screen.

To utilize this feature if your Bluetooth® audio player is not already paired as a phone, press the SETTING button on the control panel. After touching the BLUETOOTH key on the display screen, touch the CONNECT BLUETOOTH key.

The next screen asks you if you are connecting the device to use with the Hands-Free Phone system. Touch the NO key. Enter a PIN of your choice on the touchscreen and then enter the same PIN into the Bluetooth® audio device to complete the connection process.

Check your audio device's Owner's Manual for more information.

Once the device is connected, press the DISC-AUXILIARY button several times until "Bluetooth Audio" appears on the display screen. Touch the on-screen keys to pause or play the audio files.

Your device's audio files will now play through the vehicle's speakers. In some cases, the sound quality is compromised through the Bluetooth® connection. If this occurs, we recommend using the USB audio input.

Please be aware that selecting or pairing a Bluetooth® audio player may not be available immediately after starting the vehicle. Allow a short time for the paired device's phonebook to update before selecting or pairing a Bluetooth® audio player.

For more information on your Bluetooth® system, see your Owner's Manual.
 

·
Registered
Joined
·
361 Posts
Discussion Starter · #8 ·
2014 Infiniti QX50 - Seat Belt Warning Light and Chime


These important features remind you to fasten seat belts. The light illuminates whenever the ignition is in the ON position. It stays on until the driver's seat belt is fastened. The chime also sounds for a period of time unless the driver's seat belt is secured.

The seat belt warning light may also illuminate if the front passenger's seat belt is not fastened when the front passenger's seat is occupied.

It will not go on for a period of time after the ignition is turned ON, allowing time for the passenger to buckle up.




2014 Infiniti QX50 - Manual Shift Mode


Shift ranges can be selected manually when the shift lever is placed in the manual shift gate. In the manual shift mode, the shift range is displayed on the position indicator in the meter. While in the manual shift mode:

• Moving the selector lever to the + (or up) side will shift the transmission to a higher range.
• Moving the selector lever to the -- (or down) side will shift the transmission to a lower range.

Use 7th gear for all normal forward driving at highway speeds.

Use 5th and 6th gear when driving up long slopes, or for engine braking when driving down long slopes.

4th through 2nd gears can also be used for hill climbing or engine braking on downhill grades.

1st gear can be used for climbing steep hills slowly, driving slowly, or for maximum engine braking on steep downhill grades.

Do not drive at high speeds for extended periods of time in lower than 7th gear. This reduces fuel economy.

To cancel the manual shift mode, return the shift lever to the normal driving mode.




2014 Infiniti QX50 - Navigation System Overview (if so equipped)


The INFINITI Navigation System, if so equipped, uses a real-time map display and turn-by-turn voice instructions to help you navigate to your destination.

The Navigation System starts when the ignition is in the ACC or ON position.

This is your Navigation System's control panel. Use the touchscreen to select items on the screen. You can also highlight items with the INFINITI Controller and then select them by pressing the ENTER button.

The INFINITI Navigation System also has a directory of places of interest to assist the driver in finding locations, including:

• Gas stations,
• ATMs,
• Restaurants,
• Shopping centers, and
• Businesses.

Once a destination is set and a route has been calculated, the system can provide:

• The turning direction at the next intersection,
• The name of the next street,
• The distance to the next intersection or to the end destination, and
• The estimated remaining time of travel to the destination.




2014 Infiniti QX50 - Automatic Intake Air Control


To give you and your passengers cleaner air recirculation, your vehicle may be equipped with Automatic Intake Air Control.

To activate the automatic intake control mode, push and hold the auto recirculation button and the indicator light will blink twice, indicating that the system is in the automatic control mode.

When this is on, the air intake will be controlled automatically based on outside air quality.

When the system detects odors in the outside air it will automatically change to recirculation to reduce odors coming into the vehicle.

When the air quality improves it will automatically return to fresh air ventilation.

To manually select air recirculation inside the vehicle, press the recirculation button and the indicator light will illuminate.




2014 Infiniti QX50 - Navigation System Owner's Manual (if so equipped)


If your vehicle is equipped with the Navigation System, you will have received a special Navigation System Owner's Manual. It supplements this brief introduction, covering many more topics in greater detail.

It contains system information, technical information and a useful Troubleshooting Guide. This special Owner's Manual will help you become familiar with all the features of your Navigation System, offering you maximum efficiency and convenience as a traveling companion, guide and aid.
 

·
Registered
Joined
·
361 Posts
Discussion Starter · #9 ·
2014 Infiniti QX50 - Tilt/Telescopic Steering Column


If your vehicle is equipped with a power tilt and telescopic steering column, use this switch to adjust the steering wheel to the desired position.

Push the switch up, down, forward or backward to move the steering wheel in the corresponding direction.

If your vehicle is equipped with the Automatic Drive Positioner system, and it is activated, the steering wheel will move up automatically when the driver's door is opened and the ignition switch is placed in the LOCK position.

It will move back into position when the driver's door is closed and the ignition switch is placed in the ACC or ON position or the Intelligent Key is placed in the key port.

If your vehicle is equipped with a manual tilt and telescopic steering column, please see your Owner's Manual.




2014 Infiniti QX50 - Liftgate


To open your liftgate, unlock all of your doors, and then look just above the license plate under this trim panel. There you'll find the concealed OPENER switch. Push the switch while pulling up on the liftgate. To close, lower and gently push the liftgate down.

If your battery is discharged and the liftgate cannot be opened, remove this cover at the bottom of the inside of the liftgate. Beneath the cover is a lever. Move it to the right to open the liftgate.

Do not drive with the liftgate open. Always check to make sure it has closed completely to prevent it from accidentally opening while on the road. For more information on liftgate safety, see your Owner's Manual.




2014 Infiniti QX50 - All-Wheel Drive (AWD) (if so equipped)


The Intelligent All-Wheel Drive (AWD) System provides power to the wheels that need it, when they need it. The Intelligent All-Wheel Drive system instantly adapts to the changing conditions of the road by constantly monitoring wheel spin, throttle position, and vehicle speed.

This system will divert up to 50% of the available power to the front wheels to enhance traction.

Indicators regarding the status of the Intelligent AWD system are shown in the Vehicle Information Display. See your Owner's Manual for more information.




2014 Infiniti QX50 - Hazard Warning Flasher Switch


The Hazard Warning Flasher Switch is located below the center display. Push the switch on to warn other drivers when you must stop or park under emergency conditions. All turn signal lights flash and will operate with the ignition switch placed in any position. Push the switch again to turn OFF your hazard warning flashers.




2014 Infiniti QX50 - Control Panel and Touch Screen Overview


Located on the center console is the information center for your vehicle. It consists of a touchscreen display and these control panel buttons, which you can use to view information and adjust settings for Navigation, Audio, Bluetooth and other vehicle systems.

Press the INFO button to view various types of vehicle information, or press the SETTING button to access a list of settings that can be adjusted to your preference. Press the STATUS button to cycle through Navigation, fuel economy and climate control information on the screen.

There are two ways to select and adjust items on the screen.

The first is to use the touchscreen. Touch an item on the screen to select.

Touch the plus "+" key or minus "-" key to adjust the settings of an item.

Touch these arrows to scroll up or down the page one item at a time. When multiple pages of options are available, touching these double arrows scrolls up or down an entire page.

The second method for viewing and adjusting information is with the INFINITI controller. You can either rotate the dial or push it in any direction to select an item on the screen. Once the desired item is highlighted, press the ENTER button at the center of the dial to select.

After the operation is complete, press the BACK button to return to the previous screen.
 

·
Registered
Joined
·
361 Posts
Discussion Starter · #10 ·
2014 Infiniti QX50 - Receiving and Ending a Call (if so equipped)


To answer an incoming call, press the PHONE/SEND button on the steering wheel or touch the ANSWER key on the display screen.

While a call is active, touch USE HANDSET to transfer the call to your phone. Touch MUTE to mute your voice to the other end of the call. To display a keypad on the screen to input more digits during a call, touch KEYPAD.

When you wish to end a call, press the PHONE/SEND button on the steering wheel again or touch HANG UP on the display screen.




2014 Infiniti QX50 - Functions Disabled While Driving (if so equipped)


For safety, some functions cannot be operated while you are driving. They will be "grayed out," or muted on the screen. To operate them, park the vehicle in a safe location, and then operate your Navigation System before resuming.




2014 Infiniti QX50 - Vehicle Phonebook (if so equipped)


There are two ways to update the vehicle's phonebook, automatically or manually.

If compatible, the phonebook entries on your phone will begin transferring to the vehicle immediately after the phone is first connected. If this doesn't happen automatically, you can take a few simple steps to initiate the process.

Press the SETTING button on the control panel and then touch the PHONE key on the display screen. The AUTO DOWNLOADED key should have an amber indicator next to the word ON. Touch this key to toggle the feature on if necessary.

Up to 1000 entries can be automatically transferred to the vehicle. These entries can be accessed by touching PHONEBOOK on the phone main menu screen. The Voice Recognition system assigns tags to these entries for voice command dialing.

The entire transfer process can take up to five minutes to complete, depending on the size of the handset phonebook. For more information, please see the manufacturer owner's manual that came with your cellular phone.

If the phonebook does not automatically download, you can manually create entries in the quick dial. To do this, press the PHONE/SEND button on the steering wheel and then touch QUICK DIAL on the display screen. Next, touch the ADD NEW key and choose a method for entering a phone number.

For example, touch ENTER NUMBER BY KEYPAD to input the phone number using a keypad on the touchscreen. Once the number is entered, touch VOICETAG to record a voicetag for dialing with the Voice Recognition system. After the phonebook entry is saved, a screen appears that allows you to call the number. Touch BACK to return to the Quick Dial and repeat the steps for each number you'd like to store.




2014 Infiniti QX50 - Interior Storage


Your vehicle has a traditional glove box compartment. To open it, pull this handle up and lower the lid. When you want to lock or unlock the glove box, use your mechanical key. For the safety of your glove box contents, the Intelligent Key cannot be used to unlock the glove box.

Your console storage box is located between the front seats. To open the console box, push the button at the front of the console.

There are cup holders and bottle holders located conveniently in the center console and the rear seat armrest.

The sunglasses holder is opened by a push and release motion.

INFINITI strategically placed hooks throughout the cargo area. Use these hooks to secure all cargo with ropes or straps.

There are also a variety of storage bins, trays and map pockets located throughout the vehicle.




2014 Infiniti QX50 - Warning and Indicator Lights


The warning and indicator lights on your vehicle will help you stay aware of many systems and their operation.

Please see your Owner's Manual for important safety information, system limitations and additional operating information.
 

·
Registered
Joined
·
361 Posts
Discussion Starter · #11 ·
2014 Infiniti QX50 - Automatic Anti-Glare Rearview Mirror (if so equipped)


Your vehicle's rearview mirror may have a feature that enables it to detect glare and automatically dim the mirror surface.

The indicator light will illuminate when the anti-glare feature is operating. Press the OFF button to turn the anti-glare feature OFF. Press the ON button, to turn it on.

If your mirror doesn't look like this, please see your Owner's Manual.




2014 Infiniti QX50 - Distance Control Assist (DCA) (if so equipped)


To turn on the Distance Control Assist (or DCA) System, push the dynamic driver assistance switch on the steering wheel after starting the engine. The DCA system switch indicator light in the vehicle information display will illuminate. Push the dynamic driver assistance switch again to turn off the DCA system. The DCA system switch indicator light will turn off.

The system will start to operate after the vehicle speed becomes above approximately 3 miles-per-hour.

The dynamic driver assistance switch is used for both the LDP and DCA system. When the dynamic driver assistance switch is pushed, the LDP system will also turn on or off simultaneously. The DCA system can be individually set to on or off on the display. If the system is set to off, the system will not turn on even if the dynamic driver assistance switch is pushed to on.

Setting DCA system to ON or OFF:

1. Push the SETTING button.
2. Press the "Driver Assistance" key.
3. Press the "Dynamic Assistance settings" key.
4. Press the "Distance Control Assist" key to toggle between ON and OFF.

If both the Lane Departure Prevention (LDP) and DCA systems are set to OFF on the display, when the dynamic driver assistance switch is pushed, the LDP ON indicator light and the DCA system switch indicator light will blink for approximately 2 seconds.

Please see your Owner's Manual for important safety information, system limitations and additional operating information.




2014 Infiniti QX50 - Vehicle Phonebook Non-Navi (if so equipped)


The phonebook stores up to 1,000 names for each phone connected to the vehicle. Your vehicle's Bluetooth® system may automatically download your cell phone's entire phonebook, if your cell phone allows this function.

If the phonebook does not download automatically, 40 entries can be individually downloaded.

To manually download entries:
• Push the PHONE/SEND button on the steering wheel.
• After the tone, say "Phonebook."
• After the next tone, say "Transfer Entry."
• The system acknowledges the command and asks you to initiate the transfer from the phone handset.
• The new contact phone number will be transferred from the cellular phone to the vehicle.

The transfer procedure varies according to each cellular phone. See your cellular phone manufacturer's Owner's Manual for details.

You can also visit Infiniti Bluetooth | Wireless Phone Technology | Infiniti USA for instructions on transferring phone numbers from INFINITI recommended cellular phones.




2014 Infiniti QX50 - Power Outlets


There are power outlets for small electrical devices, such as cellular phones, in two areas of the cabin --the center console and below the climate controls.

The power outlets in the vehicle work when the ignition switch is in the ACC or ON position.

Leaving a device connected to the power outlet with the ignition left in the ACC or ON position can discharge the battery and the vehicle may not start.

To access a power outlet, simply open the cap.

Please see the manufacturer's Owner's Manual supplied with your device for detailed information when connecting the device to an outlet.



2014 Infiniti QX50 - Heated Seats (if so equipped)


If your vehicle is equipped with heated front seats, the control knobs are located on the center console and can be operated independently of each other.

To operate the heated front seats, start the engine. Then, turn the control knob to the right and select the desired heat range. For high heat, turn the knob to the right. For low heat, turn the knob to the left. The indicator light will illuminate when the heater is on.

To turn off the heater, return the knob to the OFF position. Make sure that the indicator light turns off.

The heated front seats automatically turn on and off to maintain the desired temperature. The indicator light will remain on as long as the switch is on. Be sure to turn the switch off when the seat is warmed, or before you leave the vehicle.
 

·
Registered
Joined
·
361 Posts
Discussion Starter · #12 ·
2014 Infiniti QX50 - Voice Adaptation Non-Navi (if so equipped)


The voice adaptation mode allows up to two users with different dialects to train the system to improve recognition accuracy. By repeating a number of commands, the users can create a voice model of their own voice that is stored in the system. The system is capable of storing a different voice adaptation model for each connected phone.

The training procedure is as follows:

1. Position the vehicle in a reasonably quiet outdoor location.

2. Sit in the driver's seat with the engine running, the parking brake on, and the transmission in Park.

3. Press the PHONE/SEND button.

4. Say "Help." The system acknowledges the command and announces the next set of available commands.

5. Say "Voice Adaptation." The system acknowledges the command and displays the voice adaptation mode screen.

6. Voice memory A or memory B is selected automatically. If both memory locations are already in use, the system will prompt you to overwrite one. Follow the instructions provided by the system.

7. When preparation is complete and you are ready to begin, press the PHONE SEND button.

8. The voice adaptation mode will be explained. Follow the instructions provided by the system. During the Voice Adaptation mode, the system instructs you to say phrases that it uses to personalize the voice recognition system.

9. When training is finished, the system will tell you an adequate number of phrases have been recorded.

10. The system will ask you to say your name. Follow the instructions to register your name.

11. The system will announce that voice adaptation has been completed and the system is ready.

The voice adaptation mode will stop if:
• The PHONE/END button is pressed.
• The vehicle is driven, or
• The ignition switch is placed in the OFF or LOCK position.




2014 Infiniti QX50 - Steering Wheel Audio Controls with Navigation


The steering wheel audio controls are located on the left side of the steering wheel.

For vehicles not equipped with the Navigation System, please see your Owner's Manual for more information.

Press the SOURCE button to turn the audio system on. Press repeatedly to cycle through the various audio modes. The CD, DVD, AUX, USB and iPod® modes are only available when compatible media is in use.

This is the menu control switch. Push up or down for less than 1.5 seconds while in AM, FM or Sirius XM modes to move through the preset stations for the selected radio band. If the switch is pushed and held for more than 1.5 seconds, the radio will seek up or down for the next broadcasting station for AM or FM or the next category for Sirius XM Satellite Radio.

Push the menu control switch up or down for less than 1.5 seconds to move forward or back through the available tracks when in CD, iPod®, USB or Bluetooth® streaming audio mode. Push up or down and hold for more than 1.5 seconds to move through folders on a USB device or CD with compressed audio files.

In most audio modes, the menu control switch can be pushed inward to access a station list or additional menus. See your Owner's Manual for more information.




2014 Infiniti QX50 - Route Button (if so equipped)


Once a destination has been set, press the ROUTE button on the control panel to display the Route Menu, where you can adjust route and guidance settings and access detour information.

This menu can also be used to edit, cancel, resume or recalculate a route.

To adjust the route settings:

• Press the ROUTE button,
• Touch ROUTE SETTINGS, then,
• Touch BASIC ROUTE TYPE to calculate the fastest route, shortest route, or a route with minimal use of freeways, or
• Touch OTHER ROUTING CHOICES to adjust settings for traffic, toll roads, ferries and areas to avoid.

When the conditions are set, the system starts calculating the route with your new request, and the current location map screen is displayed.

Up to six destinations or waypoints can be set for a route. To add a destination or a waypoint:

• Press the ROUTE button,
• Touch EDIT/ADD TO ROUTE, then
• Touch ADD DESTINATION or ADD WAYPOINT.

To cancel a route:

• Press the ROUTE button,
• Touch CANCEL ROUTE, then
• Touch YES to confirm.

If you cancel a route, the destination is not completely deleted and is available to be reactivated as long as another route is not stored.

To reactivate a canceled route, touch RESUME ROUTE on the Route Menu screen.

To detour from the currently set route:

• Press the ROUTE button,
• Touch DETOUR, then,
• Touch a preset distance to detour from the set route.

The DETOUR option cannot be selected if the vehicle has already deviated from the suggested route.




2014 Infiniti QX50 - Child Safety Rear Door Locks


Child safety locks help prevent the rear doors from being opened accidentally, especially when small children are in the vehicle.

The child safety lock levers are located on the edge of the rear doors.

When the lever is in the LOCK position, the door can be opened only from the outside.




2014 Infiniti QX50 - Front Passenger Air Bag Status Light


The front passenger air bag shuts OFF and the status light illuminates when the seat is occupied by a small adult, a child or a child restraint system. The status light will turn OFF when the air bag is ON and the front seat is occupied by an adult. Please see your Owner's Manual for a complete understanding of the operation and safety precautions for this system.
 

·
Registered
Joined
·
361 Posts
Discussion Starter · #13 ·
2014 Infiniti QX50 - Connecting Procedure


To connect your phone, the vehicle must be stationary. Press the PHONE/SEND button on the steering wheel and touch the CONNECT PHONE key on the display screen.

A popup message will appear on the screen advising you that the system is searching for your phone. From your phone's Bluetooth® settings, locate and select a device called "My Car." When prompted by the phone, input the PIN code 1-2-3-4, which will be shown on the vehicle's display screen. This PIN cannot be changed.

If your phone supports automatic download, its phonebook entries will be automatically transferred to the vehicle. When the connecting procedure is complete, the display screen returns to the PHONE menu screen.

You can also use your paired phone as a Bluetooth® audio device. See your Owner's Manual or the Bluetooth® Streaming Audio video for more information on this topic.

You may connect up to five compatible Bluetooth® devices. The connecting procedure varies according to each cellular phone model. A Compatibility Guide that identifies brands and models of phones that are compatible with your vehicle's Bluetooth® wireless technology system can be found at Infiniti Bluetooth | Wireless Phone Technology | Infiniti USA.

If your phone is not listed, this does not necessarily mean that it's incompatible. However, the website will not be able to offer further assistance for that phone. In this case, please see the manufacturer's owner's manual for further details.




2014 Infiniti QX50 - Voice Prompt Interrupt Non-Navi (if so equipped)


When using the Voice Recognition system, it is possible to skip the system's voice prompts.

Press the PHONE/SEND button on the left side of the steering wheel, the system responds with a list of instructions or available commands. It is not necessary to wait for the system to finish speaking.

Simply press the PHONE/SEND button a second time when the system is giving audio voice commands. You can speak a command once the tone sounds.

This procedure can be repeated any time you wish to interrupt the voice prompt.




2014 Infiniti QX50 - Hood Release


To open the hood, pull this HOOD RELEASE handle located below the driver's side instrument panel. Pull it and the hood will spring up slightly.

Outside the vehicle, pull this lever at the front of the hood upward as shown.

To close the hood, slowly lower it until it nears the latch, then push the hood down to lock it securely into place.




2014 Infiniti QX50 - Vehicle Information Display


Located between the vehicle's speedometer and tachometer is the Vehicle Information Display. It displays operational information such as:
• Automatic transmission position indicator
• Distance Control Assist (DCA) system (if so equipped)
• Intelligent Key operation
• Cruise Control and Intelligent Cruise Control (ICC) (if so equipped)
• Trip Computer
• Tire Pressure
• Fuel Economy, and
• Other warnings and information.

One of the vehicle information display modes is the Trip Computer. When this button is pressed, the following modes will appear on the vehicle information display:
• MPG -- Displays the current fuel consumption.
• MPG/MPH -- Displays the average fuel consumption and speed since the last reset.
• TIME/MILES -- Shows the elapsed time and total distance the vehicle has been driven since the last reset.
• RANGE -- Displays the estimated Distance To Empty (DTE) the vehicle can be driven before refueling.
• OUTSIDE TEMP -- Gives the exterior air temperature including a low temperature warning feature.
• SETTING -- Allows you to set reminders for alerts and maintenance intervals or change the language and units used in the system.
• WARNINGs -- If there are any.

In the Setting and Warning screen, press this button to cycle through the various modes available. Press this button to choose the selected menu.

Just below the vehicle information display, you'll find the odometer and twin trip odometer which are displayed when the ignition switch is in the ON position.

The odometer records the total distance the vehicle has been driven, while the twin trip odometer records the distance of two individual trips. You'll see the TRIP A/B RESET switch on the left side of the instrument panel. Push it to change the display from trip A to trip B and back again. Push and hold the switch for more than one second to reset the selected odometer.

For more information, see your Owner's Manual.




2014 Infiniti QX50 - Connecting Procedure Non-Navi (if so equipped)


To connect a compatible cellular phone, the vehicle must be stationary.

Press the PHONE SEND button on the steering wheel. The system announces the available commands. After the tone, say "Connect Phone." The system announces the next set of available commands. Say "Add Phone" after the tone.

When the command is acknowledged, the system directs you initiate the connecting procedure on your phone. When prompted for a PIN code, enter "1234" on the handset. The PIN code "1234" is assigned by INFINITI and cannot be changed.

To complete the process, the system prompts you to speak a name for the phone.

After the initial connecting procedure is complete, your phone will be automatically connected to the in-vehicle phone module whenever the ignition switch is placed in the ON position and the phone is turned on and carried into the vehicle.

You can use the same procedure to connect up to five different cellular phones to your vehicle's Bluetooth® system.

The connecting procedure varies according to each cellular phone model. A Compatibility Guide that identifies brands and models of phones that are compatible with your vehicle's Bluetooth® wireless technology system can be found at Infiniti Bluetooth | Wireless Phone Technology | Infiniti USA.

If your phone is not listed, this does not necessarily mean that it's incompatible. However, the website will not be able to offer further assistance for that phone. In this case, please see the manufacturer's owner's manual for further details.
 

·
Registered
Joined
·
361 Posts
Discussion Starter · #14 ·
2014 Infiniti QX50 - Bluetooth® Hands-free Phone System with Navigation Operating Tips


These controls allow you to operate the Bluetooth® system from your steering wheel. Here are some helpful tips to get the most out of your Bluetooth® system.

• For recommended phones and detailed instructions for connecting a compatible cellular phone, please visit Infiniti Bluetooth | Wireless Phone Technology | Infiniti USA.
• When using the Bluetooth® system, keep the interior of your vehicle as quiet as possible. Close windows and direct air vents away from the roof and your face.
• To operate the voice recognition system, press and release the TALK button on the steering wheel. The in-vehicle microphone receives the command and the system provides voice feedback when the command is accepted.
• When speaking a command, wait until the system tone sounds and the face icon on the display changes. Begin speaking within five seconds after the tone.
• Speak in a natural voice without pausing between words.
• You can press the TALK button to skip prompts at any time.
• The HELP command can be used at any time to hear a list of available commands.
• When speaking phonebook names, please be aware some phones require the last name to be spoken before the first name. For example, "Michael Smith" may be spoken as "Smith, Michael."
• Use single digits when speaking phone numbers. For example, "five hundred" should be spoken as "five zero zero."
• To increase or decrease the volume of the phone prompts, push the plus or minus volume control switches on the steering wheel, or turn the volume control dial on the audio system if in operation.
• To cancel a voice recognition session, press and hold the TALK button.

For more information on your Bluetooth® system, see your Owner's Manual or visit Infiniti Bluetooth | Wireless Phone Technology | Infiniti USA.




2014 Infiniti QX50 - Automatic Door Locks


Your vehicle is equipped with automatic door locks.

All doors lock automatically when the vehicle speed reaches approximately 15 miles per hour, and unless deactivated, unlock when the ignition is placed in the OFF position.

To unlock the door manually, use the inside lock knob or the driver's or passenger's power door lock switch.

Please see your Owner's Manual for more information.




2014 Infiniti QX50 - Climate Controls


This is one of the available climate control panels for your vehicle. If your vehicle is equipped with a different climate control system, see your Owner's Manual for additional information.

The Auto mode may be used all year round. The system automatically regulates and maintains fan speed, airflow and temperature in the cabin. To turn the system ON, press the AUTO button. The indicator light turns ON when the system is activated.

Pressing the DEFROST button or changing the fan speed or airflow mode turns off the AUTO function and switches the system to manual control. To reactivate automatic control, press the AUTO button.

To turn the entire climate control system OFF, press the OFF button.

Your vehicle has separate temperature control buttons for the driver and front seat passenger. Turn the driver's side control knob to the right for warmer or left for a cooler temperature.

If you want to adjust the passenger side temperature independently from the driver's side, press the DUAL button or turn the temperature control knob left or right. The DUAL control indicator and the passenger's side temperature will be displayed on the monitor.

If the DUAL mode is not active, the driver's temperature control buttons set the temperature for both the driver and passenger. To switch back to driver control when the DUAL mode is active, press the DUAL button again.

Press the air flow control button repeatedly to cycle through these four air flow choices:
• Air will flow from center and side vents.
• Air will flow from center, and side and foot outlets.
• Air will flow mainly from foot outlets.
• Air will flow from the defroster and foot outlets.

The selected air flow mode is displayed on the monitor.

Press the A/C button to manually turn the air conditioning ON or OFF.

Intake air control is automatically regulated in AUTO mode. Press the intake air control button to manually alternate between recirculating inside air and drawing outside air into the cabin. The indicator light on the button will illuminate when the recirculating mode is active.

The air recirculation mode increases air conditioning efficiency and helps block outside odors from entering the cabin.

To return to automatic control of the air intake mode, press and hold the air intake control button for approximately 2 seconds until the indicator light flashes twice.

Use the fan speed control buttons to adjust the fan speed. Press this button to increase fan speed. Press this button to decrease fan speed. When you manually change fan speeds, it turns off the automatic climate control mode. To return to automatic climate control, press the AUTO button.

To defrost or defog the front and side windows, press the DEFROST button. The indicator light will illuminate. Airflow will be directed to the front and side windows.

In the DEFROST mode, the Air Conditioner activates automatically at temperatures above 23 degrees Fahrenheit and the air recirculate mode automatically turns off, allowing outside air to be drawn into the passenger compartment to improve the defogging and deicing performance. For windshield deicing, the temperature and fan speed should be at the highest settings.

To defrost or defog the rear window and outside mirrors, push the REAR WINDOW DEFROSTER switch. The indicator light will illuminate. After defrosting, push the switch again to turn OFF. If not turned OFF manually, this feature will automatically deactivate after a period of time.

There is a temperature sensor located on top of the dashboard near the windshield that helps regulate the automatic climate control settings. Keep this area clear of papers and other materials.




2014 Infiniti QX50 - Alternate Command Mode (One Step Calling) (if so equipped)


The Alternate Command Mode provides an expanded list of voice commands for controlling the Phone, Vehicle Information, Audio, Display and Navigation systems.

To activate the Alternate Command Mode, press the SETTING button on the control panel, and then touch the OTHERS key on the display screen. Touch the VOICE RECOGNITION key, and then touch the ALTERNATE COMMAND MODE key. A confirmation message will appear on the screen. Touch OK to confirm activation of the ALTERNATE COMMAND MODE.

If your cellular phone is capable and your phonebook is downloaded, it is possible to interrupt the voice prompts for quicker dialing.
• Press the TALK button on the steering wheel.
• When the system command begins, press the TALK button again.
• Say "CALL" and then the name of the entry, such as "Call John Smith."
Please see your Owner's Manual or the vehicle phonebook chapter in the Bluetooth® Hands-Free Phone System with Navigation section of this electronic quick reference guide for information on downloading your phonebook.
A variety of additional commands are available, including:

• "Places," for setting as the destination a point of interest near the current vehicle location,
• "Traffic Information," to turn the traffic information system on and off, and
• "Audio Source," for example "Bluetooth® Audio" or "XM," to switch the audio system to that source.

While in Alternate Command Mode the system will not announce or display any of the available commands. To become familiar with the Alternate Command Mode commands, press the TALK button on the steering wheel and say "Help" after the tone. The system will display the command list main menu.

Another way to view the command list is to press the INFO button on the control panel, touch OTHERS, then VOICE RECOGNITION, then COMMAND LIST.

See your Owner's Manual for more information on the Bluetooth® system and the ALTERNATE COMMAND MODE.




2014 Infiniti QX50 - Power Windows


The power windows function operates when the ignition switch is placed in the ON position, and for a short time after the vehicle is turned off. The power is immediately canceled if the driver's or passenger's door is opened after the ignition switch is placed in the OFF position.

These switches located on the driver's door panel allow the driver to open or close all windows.

Your vehicle is equipped with Automatic windows. Push the switch down completely and release for the window to fully open. Pull the switch up to the highest position and release and the window will close automatically.

To stop the opening or closing of a window at any point, push or pull the switch in the opposite direction.

Press the window lock button to disable the power window switches on the passenger doors. To return power to these switches, press the window lock button a second time.

If the power window automatic function (closing only) does not operate properly, perform the following procedure to initialize the power window system.

1. Push the ignition switch to the ON position.
2. Close the door.
3. Open the window completely by operating the power window switch.
4. Pull the power window switch up and hold it to close to the window, and then hold the switch more than 3 seconds after the window is completely closed.
5. Release the power window switch. Operate the window by the automatic function to confirm the initialization is complete.
6. Perform steps 2 through 5 for other windows.

If the power window automatic function does not operate properly after performing the procedure, have your vehicle checked by an INFINITI retailer.
 

·
Registered
Joined
·
361 Posts
Discussion Starter · #15 ·
2014 Infiniti QX50 - Shoulder Belt Height Adjustment


The front outboard seatbelts can be adjusted to the position best for you.

To adjust the seatbelt height so that the shoulder seatbelt passes over the center of the shoulder, press and hold the button on the shoulder belt anchor located above the seatbelt on the pillar. Move the anchor to the desired position and release the button to lock the shoulder belt anchor into position.

The belt should be away from your face and neck, but not falling off the shoulder.




2014 Infiniti QX50 - Child Restraint Systems


This vehicle is equipped with the Lower Anchors and Tethers for Children (or LATCH) system, which includes lower anchors and top tether anchors. Please see to your Owner's Manual to find out which seating positions are equipped with anchor points.

The seat belts in your vehicle can also be used to secure the child restraint. For details on the proper installation of child restraint systems, please read the child restraint Owner's Manual and the special section in your vehicle's Owner's Manual.

You can also check the Infiniti Snug Kids® Child Restraint System Fit Guide for your vehicle. The Snug Kids® Child Restraint System Fit Guide helps parents confidently select a CRS that fits their vehicle and also provides valuable tips on the proper installation of a CRS. You can find the Snug Kids® Child Restraint System Fit Guide at www.InfinitiUSA.com/snugkids.




2014 Infiniti QX50 - Voice Guidance (if so equipped)


Your Navigation System's voice guidance function makes pertinent announcements when you approach an intersection, corner, or other guidepost along the route. It gives turning instructions and announces the remaining distance to the destination. Directions are given in ample time to prepare and proceed.

Press the VOICE button on the control panel to repeat voice guidance.

To turn the voice guidance ON or OFF:

• Press the ROUTE button,
• Touch GUIDANCE SETTINGS, then
• Touch GUIDANCE VOICE to toggle the feature on or off.

The indicator illuminates if voice guidance is activated.

To adjust the volume, touch GUIDANCE VOLUME on the GUIDANCE SETTINGS menu and then touch the PLUS or MINUS key to raise or lower the volume.
 

·
Registered
Joined
·
81 Posts
amazing, this will come in handy since a lot of people don't bother looking at their owners manual instead they come on forums like this to ask questions that could have been answered in the manual :D
 
1 - 17 of 17 Posts
Top